1 [email protected]:8’2” or 2.49m12 x 12 Arched Roof Pergolawith PlinthInstallation and Operating Instructions – YM11635Yardistry
10 [email protected]. - Trim Screw #6 x 30mm - (Y06420-910)8pc.- LMountLeft-(Y00419-004)8pc. - Wafer Bolt 1/4 x 3-3/4" - (Y
11 [email protected] NUMBER: YM11635CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 1)CARTON I.D. STAMP: __ __ __ __ __ __
12 [email protected] 2: Assemble “X” Inserts 64 x X Insert 38.1 x 38.1 x 574.7 mm (2 x 2 x 22-5/8”)HardwareWood PartsFig. 2.
13 [email protected] 3: Assemble 8 Panels Part 1HardwareWood PartsNote: You will be assembling 8 Panel Post Assemblies in total i
14 [email protected] PartsC: Slide one complete Insert in from the top of the panels and down to the (185) Horizontal Ins
15 [email protected] 4: Attach Panel Posts to Corner Posts Part 1A: On Engineered Panel Corner Post, per assembly, pre-drill two
16 [email protected] 4: Attach Panel Posts to Corner Posts Part 2HardwareWood Parts 8 x #10 x 4” Wood Screw 24 x #8 x 2-1/2”
17 [email protected]: Pre-drill with a 1/8” drill bit and attach two L Mounts (one L Mount Right and one L Mount Left) ush to the i
18 [email protected] Parts#6 x 30 mm Trim Screw(028) Plinth Short B AssemblyPlinths rest on top of the L Mounts(027) Plint
19 [email protected] Parts#6 x 30 mm Trim Screwx 2 per board Flush(026)Plinth Long AssemblyStep 6: Attach Plinths to Corne
2 [email protected] Safety Notice!Yardistry components are intended for privacy, decorative and ornamental use only.Product is
20 [email protected] Parts#6 x 30 mm Trim Screwx 4 per board Flush(029) Plinth End AssemblyNote: Loosen screws as necessar
21 [email protected]#6 x 30 mm Trim ScrewStep 6: Attach Plinths to Corner Post AssemblyPart 4Note: Make sure all plinths are
22 [email protected] 169 11/16" 120X478.5X4 78.5 120 120 78.5 169 11/16" move to final positionStep 7: Locate Corner Pos
23 [email protected] Beam Ends attached on cut-out sideStep 8: Assemble Beam Ends 4 x (192) Beam End 34-1/4” 38.1 x 139.7 x 870
24 [email protected] is important the proper hardware gets placed in the places shown. You install the Wafer Bolt rst and then the
25 [email protected] is important the proper hardware gets placed in the places shown. Make sure you install the Wafer Bolt rst an
26 [email protected] is important the proper hardware gets placed in the places shown.A: Attach one (080) Arch Beam Offset through
27 [email protected]: On a at and level surface, t together one (062) Trellis End 33-1/2” and one (061) Trellis End 110-1/2”. (
28 [email protected]: Measure 59-1/4” from the inside of each Beam 81-1/2” and place one Trellis End Assembly on the Arch Beam Offse
29 [email protected] 12 8X 12 D: Starting at the centre Trellis End Assembly and working outwards attach four Trellis End Assemblie
3 [email protected] WarrantyYardistry warrants that this product is free from defect in materials and workmanship for a period o
30 [email protected]: The bevelled ends on each Arch Gusset should always face away from the wood it is attaching to.A: At two c
31 [email protected] 20-3/4” Panel Post#8 x 3” Wood Screw#8 x 2-1/2” Wood ScrewBevelled EndCross Brace InsertFlushArch Gusset Rig
34 [email protected] Consumer Registration CardFirst Name Initial Last NameStreet Apt. No.City State/Province ZIP/Postal
4 [email protected] for Proper MaintenanceYour Yardistry structure is designed and constructed of quality materials. As wi
5 [email protected]: It is critically important you start with square, solid and level footings, concrete pad or deck to attach you
6 [email protected] Installation Examples cont.Concrete Patio (min. 10’ 2” x 10’ 2”) with 12” clearance on all sidesWood Deck
7 [email protected] Long Assembly (026)Arch Beam Front (195)Arch Beam Offset (080)L Mount RightBeam 81-1/2" (068)Arch Gusset
8 [email protected]. (194) - Arch Gusset Left 2 x 5 x 17-27/32" - Box 14pc. (193) - Arch Gusset Right 2 x 5 x 17-27/32"
9 [email protected] 81-1/2" 2 x 6 x 81-1/2" - Box 12pc. (068) - 38.1 x 139.7 x 2070.1mmPart Identification (
Commentaires sur ces manuels